Posts in category guides

Use Aeon Labs Minimote

The Aeon Labs Minimote is a nice looking remote control for Z-Wave devices. It might be a little hard to understand the manual and the scenes and associations described though.

This remote control does not support normal association where the main controller can set the nodes in association groups. Instead this is done on the remote control itself.

The remote control can only control devices that uses Switch Multilevel and Switch Binary, that means most dimmer and most on/off devices.

To make this device control other devices set it up by following these steps:

  1. Include it into the Z-Wave network: Add a new device in Telldus Live! Press the Learn-button on the remote control
  1. Press and hold the button you like to configure - the blue led will flash after 1 sec.
  1. While still holding the button, make the device you want to control send out it's Node Information Frame. The blue led will stay steady blue.
  1. Set the dimmer level or the on/off-state you want the button to set.
  1. Release the button.

Problems with Huawei B593 4G LTE router and TellStick Net

Some users have reported problems when using TellStick Net together with the Huawei router B593. Thanks to the users Ville and Nils, there is a solution to the problem.

1. Check firewall security level.

Use the "Medium (standard)" level.

Click the image

2. Find Telldus NET MAC address in ARP table.

In this example it's on line Index8, "Unknown device". Verify that the MAC address in the list matches the one on the sticker on TellStick Net. Copy this MAC address.

3. Open Security / MAC filtering

Click the image

4. Add the MAC address to the white list

Click the image

5. Turn on ICMP

Click the image

Use Fibaro Motion Sensor

The Fibaro Motion Sensor is a really nice and small PIR with additional temperature and light sensor.

The light and temperature sensor reports are turned off by default, to activate them you'll need to set configurations 42 to 64 to desired values.

To set the interval between light reports, set configuration 42:

To set the settings for temperature, set configurations 60 to 64:

Keep in mind that this is a battery operated sensor and that it will drain more battery to send sensor values more often. Select values so that you get the reports as often as you need them.

The temperature sensor report will only be sent if the temperature differs more than the value set in configuration 60. If the temperature is very steady and the value of configuration 60 is set to eg. 1 degree, the report will be sent very rarely.

The settings will not be sent to the sensor when you press save since it's sleeping most of the time. The settings will be sent automatically on next wake up or if you wake it up manually by pressing the button three times quickly.

Regarding the wake up time, this setting should be set to a low value when you are setting up the device in order for it to wake up often and receive new settings. But after that is done you should set it to only wake up rarely to reduce the battery consumption.

Merry Christmas!

Use Aeon Labs Key Fob

Aeon Labs Key Fob

The Aeon Labs Key Fob is a nice and small remote control for Z-Wave devices, it might be a little hard to understand the manual and the different modes it has though.
In order to make it easier to use, we've put together a small guide on how to include and configure this device.

The Key Fob can act as a Primary Controller if you don't have an existing Z-Wave network, but we will include it into the TellStick ZNet Lite Z-Wave network.
Start by add a new device in Telldus Live!. Use a pin or paperclip and push the learn button located on the back side of the Key Fob.
Give the new device a name.

Until now, the Key Fob has been in the Setup mode. Now we need to change the mode to Use Mode.
Use a pin or paperclip and push the learn button and the mode button for 3 seconds.
The LED will light up red for 3 seconds and then green for 1 second, confirming the mode change.

Since TellStick ZNet Lite does not support Z-Wave Scenes at the moment, we'll need to use the group mode to control devices.
Group mode is the default mode. To check the current mode, click on the device in Telldus Live!, click Edit device, Click Configuration, Click Advanced settings, check configuration number 250, it should be set to Group mode.

Now it's time to select a device to control from the Key Fob.
The device you wish to control needs to be included to TellStick ZNet Lite.
Depending on the mode of the device when it's paired with the Key Fob, the button will act as follows:
ON - Toggle the device
OFF - Turn off the device
DIM - Toggle dim on the device.
Press and hold the button on the Key Fob that you wish to use.
Start learn mode on the device. Please refer to the manual if you're unsure how to do this.
Release the button on the Key Fob.

If the device is controlled using the same button as start learn mode, you'll need to set the correct state before you start the learn mode.
Many switches start learn mode by pressing three times on the button that also controls the device.
When pressing three times, the status will also change three times. Make sure the device is OFF before starting learn mode if you want the Key Fob button to toggle the device.